New Posts New Posts RSS Feed - Minimising surface noise of vinyl on recordings?
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Welcome to the Graham Slee Audio Products Owners Forum

 

Open to all owners plus those contemplating the purchase of a Graham Slee HiFi System Components audio product and wishing to use this forum's loaner program: join here (Rules on posting can be found here)

This website along with trade marks Graham Slee and HiFi System Components are owned by Cadman Enterprises Ltd


Minimising surface noise of vinyl on recordings?

 Post Reply Post Reply Page  12>
Author
patientot View Drop Down
Senior Member
Senior Member


Joined: 28 Nov 2018
Location: USA
Status: Offline
Points: 1523
Post Options Post Options   Thanks (0) Thanks(0)   Quote patientot Quote  Post ReplyReply Direct Link To This Post Topic: Minimising surface noise of vinyl on recordings?
    Posted: 19 Apr 2021 at 2:51pm
Originally posted by Martyk Martyk wrote:


Just using my Concorde Elektro Ortofon Stylus now but wondered the best configuration for it to pair with the Accession MM?

According to the manual its recommended is 200 - 600 pF.
I saw a load of things written on the manual about subtracting 75 to 100 but don't quite understand it and wondered if someone can assist.



Ortofon is not helping you here. That is a huge range of settings. Normally the manufacturer's recommended setting is much more narrow. When you are adding up capacitance, you have to take into account the internal tonearm wiring, the cabling that runs out the back of the turntable, and the input capacitance of the phono preamp. Typically, though not always, when you combine the internal tonearm wiring and the aforementioned cables you'll have at least ~100pf. So if the cartridge manufacturer says 200pf for a certain cartridge, you would set the phono preamp to 100pf. Make sense?

When the cartridge manufacturer doesn't tell you what to use, or gives you a broad range like 200-600pf, you're basically left to figure things out on your own. That means using an accurate test record and software, some kind of LCR modeling, or just trying to tune by ear. If it were me I'd probably just keep the capacitance on the low side as most cartridges don't benefit from jacking it way up. Of course there are exceptions.

One thing I noticed is this is a very high output cart (7.5mV) meant for DJ work.


If you can swap that cart out for something with more modest 3-5mV output, it might also help reduce the surface noise. IME carts like that Concorde can magnify surface noise. A DJ friend of mine noticed the same thing when he moved from one set with 6mV output to a set with over 8mV output.



Originally posted by Martyk Martyk wrote:


My pressings of vinyl range between the years of 1998 to 2004. Which would surely be RIAA right? All my pressings are from the UK and I have actually noticed the sound to be a lot more clearer/open on the British option rather than RIAA. On RIAA the sound sort of sounds a bit more closed in... hard to explain. Anyone else noticed?


All of those records should be RIAA records. Most of the alternative EQ curves are for records that were pressed prior to RIAA standardization in the mid 50s to early 60s. However, if you want to use an alternative EQ to listen to your records that's your prerogative.
SL-1200 MK7 (modified) + Reflex M + PSU-1 used with AT150-40ML, AT VM95ML, Stanton 680mkII + Ogura, and Shure M35X cartridges.
Back to Top
Graham Slee View Drop Down
Admin Group
Admin Group
Avatar
Retired

Joined: 11 Jan 2008
Location: South Yorkshire
Status: Offline
Points: 16298
Post Options Post Options   Thanks (2) Thanks(2)   Quote Graham Slee Quote  Post ReplyReply Direct Link To This Post Posted: 19 Apr 2021 at 8:11am
Noticed? Welcome to my world!

As designer Doug Self basically put it (20 years ago) - if after 40 years, anybody thinks solid-state amplification has been perfected, think again! (my interpretation).

Every step of the analogue way, its amplification; even if it's a buffer, it is an amplifier.

It stops being an amplifier where it crosses into the digital domain, and I'm not going to venture there. Everywhere else, it is amplification of some sort.

Many engineers play down the speed of vinyl, as it isn't really a high-frequency medium. Yeah, but you're amplifying a tiny signal, requiring serious gain, and nobody considers beta as it approaches the transition frequency. Hey, throw more transistors at it.

Every amplifier is a trapped oscillator just wanting to escape. Still, while vinyl spent its years in the underworld, designers, having discovered the simplicity of CD (the forerunner of today's digital world), stopped thinking of the reason for "speed" as it wasn't needed anymore - few being old enough to remember, and a lot more with memory loss!

Woe betides the owner of Chinese developed vinyl circuitry. As an old Chinese friend told me, "we never knew vinyl. It existed during the cultural revolution. We never knew it existed."

Luckily for me, there have been a few tens of thousands of customers owning amps having the speed to do my quiet phono stages justice.

It isn't a matter that the phono stage can magically cure all ills. It can only do so in the right company. Defining that company is the tricky part. Specifications cannot tell you. I can build an amplifier a hundred ways, and if I'm lucky, 99 don't do it for vinyl! On the other hand, all 100 will do it for digital audio.

An example is the Solo headphone amplifier history. Twenty-one years of producing a headphone amplifier that cuts the mustard for vinyl but having to create the digital wow factor to get it to sell in the cutthroat headphone amplifier market.

Yes, it can be "chip rolled", and those that do it ask why I don't do the same. It is due to getting it right for vinyl. It is likewise with power amps and just the same in a preamp. All can be easily made to sound great with digital audio, but the proof of the pudding is vinyl!

You look at your recording and playback chain. Did any of the designers burst their brain cells over it, or did they work office hours? The price tag might be an indication.

Hopefully, someone on here will talk to you about "the well-trodden path" or about being "fully Slee'd," and the reason for that is down to the compatibility of each product with a vinyl source.

The past three years I've spent developing an amplifier where vinyl exposed circuit problems. "OK, it sounds great on digital - let's try vinyl .... argh! the surface noise!" And back to "the drawing board" to burst ever more brain cells to find the function that caused it. Needles and haystacks!

The phono stage doesn't remove clicks - it doesn't emphasize them! It reproduces the original click instead of the emphasized clicks you get elsewhere.

The next stage has to do the same - not to emphasize the clicks. So what is it? I wish I could give you a straight answer, but the truth tends to require far greater explanation.

The work of Matti Otala gets the nearest, but here we were in 1972, and who wants to go so far back? Everything Otala said works - but others come along and deny overshoot, and these others are often the educators. They cannot see with Otala's mind's eye. National Semiconductor gave the world its education on designing phono stages and couldn't see it either.

The entire thing is holistic, and you'll get that dismay about EQ settings because the chain is not holistic. The 200 - 600 pf is essentially ballpark. Somewhere in there, you might find a sweet spot.

Calculate the resonant frequency range between 200 and 600 pf - use Fr = 1/ 2pi * sqrt of L * C. See how crazy and wide of any mark such a load range is, and it's much less than 20kHz!

Damp that with the 47k "standard load" and see the mismatch. Do they even tell you the cartridge's inductance? No MM tracks RIAA accurately - there's always a bump in the upper mids. Try to measure the frequency of a click. Perhaps it has a frequency-amplitude profile? What's the output of a constant velocity device?

It isn't quite as bad as answering the reason for the universe's existence and how it's held together, but it isn't far off! If clicks didn't exist, vinyl would be easy, but clicks exist in chaos, and every part of the vinyl chain has to be designed with that chaos in mind.

Answer me honestly, do they?

That none should be able to buy or sell without a smartphone and the knowledge in how to use apps
Back to Top
Martyk View Drop Down
New Member
New Member


Joined: 12 Jan 2021
Status: Offline
Points: 21
Post Options Post Options   Thanks (1) Thanks(1)   Quote Martyk Quote  Post ReplyReply Direct Link To This Post Posted: 19 Apr 2021 at 5:16am
Hi all

Thanks for all your input

Yes you were right. It is definitely surface noise which was the issue. After 3 thorough cleans on the same vinyl there is a definite improvement now. I have ordered the AI No 15 and Pure Water so fingers crossed it'll clean it in one hit rather than having to keep applying the same procedure.

However I do have another question now...

Just using my Concorde Elektro Ortofon Stylus now but wondered the best configuration for it to pair with the Accession MM?

According to the manual its recommended is 200 - 600 pF.
I saw a load of things written on the manual about subtracting 75 to 100 but don't quite understand it and wondered if someone can assist.

So I basically I just want to know the capactiance setting to apply to a Concorde Elektro Ortofon stylus which has recommended capacitance of 200 - 600 pF. Cables used is the standard Technics RCA cable which I think is good quality because its well shielded.

I also noticed on the manual (from memory) it mentions that RIAA setting are of records today and its the suggested setting to use. My pressings of vinyl range between the years of 1998 to 2004. Which would surely be RIAA right? All my pressings are from the UK and I have actually noticed the sound to be a lot more clearer/open on the British option rather than RIAA. On RIAA the sound sort of sounds a bit more closed in... hard to explain. Anyone else noticed?


Edited by Martyk - 19 Apr 2021 at 5:18am
Back to Top
Godra View Drop Down
Senior Member
Senior Member
Avatar

Joined: 29 Apr 2016
Location: Mont-Royal
Status: Offline
Points: 179
Post Options Post Options   Thanks (0) Thanks(0)   Quote Godra Quote  Post ReplyReply Direct Link To This Post Posted: 16 Apr 2021 at 2:14am
Originally posted by patientot patientot wrote:



What I might suggest you do is add a rinse cycle to your cleaning process with nothing but plain distilled water []...

If these are records that were used heavily in a club DJ environment you might want to look into a bulk ultrasonic tank cleaning situation where you can clean multiple records at a time.



My experience concurs with Patientot. Adding a rinse cycle is fundamental to get less noisy record. Also, this way you won't end up with gunk on your stylus. The rinse cycle remove the cleaning agent. 

Last year, I bought myself a cheap ultrasonic tank and wasn't fully satisfied until I took seriously the rinse step. I also added a water filter with a small pump to keep the water clean in the tank. This way you can clean a lot of records.
Clearaudio Performance DC with Clarify tonearm + Virtuoso V2, Tannoy Legacy Eaton, Accession MM and BAT VK300Xse
Back to Top
Martyk View Drop Down
New Member
New Member


Joined: 12 Jan 2021
Status: Offline
Points: 21
Post Options Post Options   Thanks (1) Thanks(1)   Quote Martyk Quote  Post ReplyReply Direct Link To This Post Posted: 14 Apr 2021 at 1:41pm
Thanks everyone for getting back

I was just about to make a fresh recording but when i peeled the record revirginizer off its left an awful mess over the record. I am pretty sure their solutions have deteriorated recently. If you're not familiar with it itsl ike a glue which cleans the records. Its very good but very expensive and have been a bit disappointed with the recent lot. The reason I am using record revirginizer instead of doing my previously mentioned way is just to get it that bit more clean. Wish i hadn't now though because its left all these strands on the record :(

I was very happy to see they sell that in Australia that you mentioned for 70 dollars a bottle. Tempted to get one! I will avoid Microfibre then. That may actually explain why i have been finding all these very small bits in the grooves.

I will get another rip uploaded tomorrow onto here as i need to go to bed now.

Will upload it shortly.

Thanks for your help :)
Back to Top
patientot View Drop Down
Senior Member
Senior Member


Joined: 28 Nov 2018
Location: USA
Status: Offline
Points: 1523
Post Options Post Options   Thanks (0) Thanks(0)   Quote patientot Quote  Post ReplyReply Direct Link To This Post Posted: 14 Apr 2021 at 1:02pm
I won't listen to the sample just yet until we know it's the right one.

Re: surface noise in general, it can vary a lot from record to record IME. Not just due to condition and wear and tear which affects all used records, but due to how the record was made in the first place.

Here in the U.S., we had plenty of records made using too much regrind. Some labels and plants were famous for it. Plenty of plants just made noisy records no matter what also. Compare that to a record pressed on Quiex II or JVC Supervinyl and it's night and day.

If we're talking about club/dance music, I can tell you the records pressed over in France, Germany, etc. were much higher quality than some of the records made at a plant here in my hometown. Just the way it is. I still have some 12''s from the 90s here.

Re: cleaning I am not a fan of microfiber at all. Back when I experimented with DIY cleaners and homebrew fluids I used microfiber towels and all they did was shed fibers into the vinyl and then deposit them on the stylus. Often you couldn't see this while using them, or even right away, but fibers would wrap around the stylus over time and be very hard to remove. As a result, ALL microfiber is banned from touching my records.

What I might suggest you do is add a rinse cycle to your cleaning process with nothing but plain distilled water. I would also cut down on the elbow grease since that's not going to help if your fluid is any good. The fluid alone with mild agitation should dislodge debris on average dusty used records, which is why I use AI #15, which is an enzyme-based record cleaner. Most of the other fluids I've tried are too weak and don't clean well enough for my taste.

If these are records that were used heavily in a club DJ environment you might want to look into a bulk ultrasonic tank cleaning situation where you can clean multiple records at a time.


SL-1200 MK7 (modified) + Reflex M + PSU-1 used with AT150-40ML, AT VM95ML, Stanton 680mkII + Ogura, and Shure M35X cartridges.
Back to Top
CageyH View Drop Down
Senior Member
Senior Member
Avatar

Joined: 30 Apr 2012
Location: Toulouse, Franc
Status: Offline
Points: 1678
Post Options Post Options   Thanks (0) Thanks(0)   Quote CageyH Quote  Post ReplyReply Direct Link To This Post Posted: 14 Apr 2021 at 12:10pm
Is the noise on every track, or only certain?
Record condition can play a part in surface noise.
Kevin
European loan coordinator, based near Toulouse, France.
Back to Top
 Post Reply Post Reply Page  12>
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.01
Copyright ©2001-2018 Web Wiz Ltd.

This page was generated in 0.117 seconds.